opens up to show off a full internal display tucked inside the two halves. Since my inner

screen was damaged during the durability test and is a bit finicky now, my question is can

I disassemble the phone and just keep one half of it as a functional device? Cuz technically

there is that one screen that still works on the outside. It should be an interesting

little experiment.

Let's get started.

[Intro]

So there are 3 surfaces to this phone: the large square inner screen, and then the two

long rectangles that are located on the outside. Samsung phones are typically taken apart by

removing the back glass and this Galaxy Fold appears to be no different. With a bit of

heat from my heat gun, and a bit of fancy finessing from my razor blade, along with

the suction cup, I can gently work my way around the back glass panel slicing through

the adhesive. It's a tad difficult since the glass is curved, but not impossible.

After the majority of the adhesive is cut, I can twist off the only piece of this phone

that doesn't have a screen attached and pull it away from the phone. There are no ribbons

or anything sensitive attached to the underside of the glass.

We do get our first look at the wireless charging coil which I totally forgot this phone even

had. Now we have two sides left. I'm going to assume that this phone has more components

under the smaller display. So I'll grab my suction cup, heat gun and razor blade, and

work my way around the glass once again, taking special care not to put my razor blade too

deep into the phone because if the screen gets poked from the underside, it'll be dead.

The screens are very fragile, as we learned from the folding screen inside of this phone.

After the adhesive is warmed up and cut away, I can tilt the screen up and away from the

hinge side, folding it open, allowing access to the thin ribbon cable plugged in underneath

the black plastic cap. Once I unsnap that like a little Lego, the front screen and glass

panel can be removed. It's a super thin compact little design. OLED screens are as thin as

they come. It's the same style of screen we saw in the back of the Nubia X. And now we

know that Samsung can do dual screens, maybe they'll start adding front and rear screens

to their other phones just because they can. No complaints here.

There are 19 visible screws holding down the internal back plastics to the phone. And three

more screws hidden underneath the wireless charging flap. After those are removed, the

wireless charging can be pulled away. This has the circular wireless coils in the center,

along with what looks like NFC coils, all of which can communicate through the gold

contact pads that rest up against the motherboard. Now I can remove the black plastics from the

right side. The top section has a built in loudspeaker, along with a separate earpiece

speaker. Kind of interesting that they are both right next to each other. Then we have

a plain black piece of plastic that brackets around the battery. And lastly, we have the

bottom plastics which contain the loudspeaker.

One cool thing about this little speaker, just like we saw in the iPhone 11 Pro, are

these little white foam dots that fill up the space inside of the speaker box. The lightweight

specs are added to the speaker housing to dampen the speaker. As the speaker moves,

air inside of the speaker box has to pass through the foamy dots, causing the air to

scatter and act less dense, which then allows the speaker to sound bigger than it actually

is. People have been adding foam to sub woofer boxes for years, so it's interesting to see

the same concept applied here on this sub woofer for ants. Someone should count these

for us.

You might have noticed already that this phone has two batteries inside: a small little guy

off to the left, and then a relatively proportional battery on the right side. I'll unplug each

of them just like little Legos. Removing the battery is the same dangerous, tedious process

that it always is with Samsungs. Even on this futuristic Galaxy Fold, Samsung still hasn't

updated their battery adhesion practices. With two pry tools gently leveraging up the

battery, I can finally remove it by hand, but any accidental bends would either cause

the battery to just slowly expand over the next several months, or explode immediately.

It's a fun little game that keeps you on your toes.

I'll remove the extensions ribbon over top of the smaller little battery. And then commence

the same gentle prying procedure while hoping nothing spontaneously combusts.

The small battery is a 2100 milliamp hour, and the larger is a 2135 for a combined total

of 4235 milliamp hours. Something I haven't noticed before is that both of the motherboards

inside the Galaxy Fold kind of glimmer with a rainbow effect. Like a gasoline drip in

a wet parking lot. It must be some kind of treatment that they use while assembling the

boards. It looks super cool. I really do think that sometimes the insides of cellphones look

cooler than the outsides. Thumbs up to Samsung for that one.

Speaking of internals, here's a close-up shot of the guts. For those of you with a Galaxy

Fold you can screenshot this, crop it, and make it a wallpaper.

Back to business, it's time to see how this hinge works and how it was able to withstand

my bend test. The SIM card tray does have a rubber ring around the lip, but there's

definitely no ingress protection rating on this phone since dust can still very easily

get inside at other points. I'll remove the 3 large ribbon connectors on this half of

the motherboard. Remember that this is also the half of the phone that the smaller rear

screen plugs into.

There's one more Phillips head screw holding the motherboard down. And then I can lift

up and unlatch the last little ribbon on the underside before pulling the motherboard free.

The shimmery motherboard comes out with the outer camera still connected. It's a 10 megapixel

camera with no optical image stabilization. There's also a large magnet along the side

and up in the corners. This helps keep the phone closed but it's pretty well balanced

without being too strong or noticeable. I'll unsnap the two large motherboard extension

ribbons from the other half of the phone. Along with the side button connector. And

I can pop out the two internal front-facing cameras.

Remember, there are 6 cameras in here. These little guys are the 10 megapixel main camera,

along with it's 8 megapixel depth sensing sidekick. Neither of which have optical image

stabilization. After popping off the two bottom signal wires, the motherboard can start lifting

away from inside the phone, and once it's out we get our first glimpse of the copper

cooling pad underneath the board.

The motherboard doesn't have any thermal paste, but it does have the foam pad to help transfer

heat. The triple camera setup on the Galaxy Fold is very similar to the Galaxy Note 10

with it's 12 megapixel 2x optical zoom camera down at the bottom. Then the 12 megapixel

main camera here in the center that also has optical image stabilization. The main camera

also has the little variable aperture gizmo. I can magnetically adjust how much light can

enter the sensor with it's little circular shutter thingies. Pretty cool. The 12 megapixel

wide-angle camera up top does not have any optical image stabilization.

Remember how I was going to take this phone apart and see if half of the Fold could still

function as a full phone? Well, both sides do have a battery. And one half has an extra

screen, so it was a good theory, but the problem is the small screen is on the opposite side

of the USB-C charging port. So the Galaxy Fold definitely needs both halves of the phone

to still function. Who would have thought?

The copper vapor chamber can pry out of the phone easy enough. This little guy just dissipates

the heat from the processor allowing the phone to run a little cooler. We've seen this kind

of copper inside of a lot of phones at this point, so let's keep going.

It's time to check out the massive internal 7.3 inch AMOLED screen and the complex hinge

contraption that holds this whole thing together. Now you probably remember that this is the

second time the Galaxy Fold has been released. The first time it launched there was what

looked like a screen protector on top, but was actually part of the screen itself. Samsung

has since extended that screen protector looking plastic component of the screen up underneath

this plastic bezel, so people now won't be tempted to peel it off. My temptation to peel

the screen off though is still pretty strong, so let's proceed.

The screen is paper thin this time, and well, you know, it's foldable. It feels like a giant

piece of thick packing tape just peeling away from the phone body. And it's rather satisfying.

Samsung has added a metal plate under each half of the phone on this new version, and

this is supposed to add a little bit of structure to the screen, at the same time while not

allowing any dust to get behind the display to cause damage since the phone body is not

dust proof. Samsung has said that anyone with a Samsung Fold can replace that inner folding

screen during the first year for a one time fee of $149 which seems more than reasonable.

But if you happen to break the screen more than once, or after that first year, it'll

be $599. Funny how Samsung can replace the whole screen for the same price that Apple's

charging to swap the back glass of an iPhone 11.

Now let's take an upclose and personal look at this hinge. This floppy boy survived my

durability test and I think it's time we found out how and why. There are some pieces of

long thin black tape covering up the internal screws. I'll pull those away from the Galaxy

Fold so we can see more of the impressive engineering. We can also see some of the sand

that slipped up inside the Fold. This is still causing a grinding noise as the phone opens

and closes. Let's take things a step further.

The hinge of the Galaxy Fold is made up of three main components: the first of which

being the massive back metal spine of the fold, and it's held in place by 10 screws.

Once those are removed, the spine can be pulled from the center of the phone. It's metal design

has chambers or ridges inside to help guide the other components of the hinge. It keeps

them from bending too far or rotating out of place. Here in the center we see the inner

gears inspired by watch mechanics, along with 3 of the 4 spring loaded clasps that lock

the Fold into the open position. It feels extremely well balanced. Inside of the Fold

we get these metal interlocked shovel looking gizmos. Two large ones in the center with

two more smaller versions at both the top and the bottom. There are a lot of moving

parts inside of this thing which does make it feel very balanced and natural while also

being incredibly sturdy. But with all the precision that these moving parts require,

there's not very much room for any specks of sand, and currently sand and dust can still

get inside and grind away to their little heart's content.

So while this hinge design was inspired by watch mechanics, hopefully Samsung can also

seal it up like watches are in future versions of the Fold. I think it's an awesome innovation

and it's good of Samsung to take care of their customers by offering replacement screens

for so cheap during that first year. I look forward to seeing what other versions of the

Fold come out next. Personally I want to see a smaller Fold that opens vertically into

a normal size cellphone. Kind of like the old school flip phones. That'll be fun to

see what happens.

Do you think folding phones are ever going to catch on and be mainstream? Let me know

down in the comments. Hit that subscribe button if you haven't already. And come hang out

with me on Instagram and Twitter. Thanks a ton for watching. I'll see you around.