Name: PCビルダーの悪夢？(曲がったCPUピンの修正) (A PC Builders Nightmare? (Fixing Bent CPU Pins))
Uploaded: 2021-01-14T09:55:22.000Z
Duration: 4 min 35 s
Description: VoiceTubeの動画で発音を聞きながら英語表現を覚えよう！学べる英語：

who have ever won and welcome to another video Now.

Earlier, I discovered that one of my old AMG Athlon CB use refused to fit in the socket.

I thought perhaps my motherboard was incompatible.

But after closer inspection, it seems that quite a few of the pins had been bent, likely due to me mishandling it at some point.

This is a super old CPU, so it may seem like no big deal.

After all, if this was a more expensive modern process, sir, it would seem like a pretty scary situation.

But fixing bent pins is easier than it seems and quite satisfying in some aspects, too.

Well, these are the tools I'm going to be using a pair of tweezers with two very fine points at the end on old and very blunt razor blade that's thin enough to fit between the rows of pins and a jeweler's loop or a very powerful magnifying glass.

This isn't totally necessary, but if like me, your eyesight is pretty bad, it helps a lot.

This will also allow you to see each individual CPU pin with total clarity.

The first thing I'm going to do here is check the rest of the process of her bent pins.

In the meantime, ignoring the clearly and severely affected area.

There are a few pins that are a little wonky, so I'm going to run the razorblade between the pins, applying gentle pressure to straighten them out.

This is why I recommend using a blunt razor, because I've accidentally sliced my hand on these before without even realizing it.

And unfortunately, blood doesn't work as a decent thermal paste.

Once we've got those few sorted out, it's time to take a closer look at the mainly affected area.

Trying to hold these two and film is somewhat more difficult than it seems.

Once again, I'm going to use the razor to straighten out the slightly bent pins here and make sure that all in line from every angle, it may look fiddly.

But the blade makes it very easy to push and pull the pins into place, which are in fact very workable and don't take much force to move.

It's easy to see why they can be bent so easily, but it means that you don't need much force to put them back into place.

I'm going to use the tweezers to maneuver, the more awkward to reach pins.

But don't pull upwards on them at all, as the last thing you want to do is rip one of them out.

Now, this may take a few minutes or hours, depending on the damage to the pins.

But just keep working at it with the blade, and eventually the pins will start to look more and more like they did when you took your shiny new or bargain used processing out of the box.

As you can see, my Athlon processes pins are starting to look a lot better now.

But I'm going to get the jeweler's loop out here and take a closer look at the pins and see if I can get them more in line.

The ends of the razor can also come in handy, as the fine point will allow you to get under any really bent over pins and lift them up.

After about 20 minutes of working on, the Cebu is time to test it out in the motherboard, you may have to try a few times as there might be one or two pins that you missed.

One of the rose might be slightly angled so the holes don't quite line up.

That seems to be the case here, and as you can see, this pin here is the likely culprit.

When there are 942 look at it's not hard to miss one or two.

This time the CPU fits, but it needed a tiny push on each corner to pop into the socket.

Usually it should just slide into the holes, but the pins are probably a little bit off angle.

In some places, though, you'll be able to feel when it wants to go in, as opposed to when there's still something wrong.

I'm going to lift the socket arm up and down a few times here to make sure the CPU is in the socket firmly.

Now you won't get the pins perfectly, 100% straight again like they were from the factory.

Try and get them is neat as possible with everything straightened out here.

Our CPU fits right back in the motherboard as it should.

Andi even boots up perfectly without any issues.

And I'm sure it will be an even friendly a sight to the O Z view out there who have a more expensive Reisen or FX CPU with a few out of place pins on it as well as always.

I wanted to make this video because I think it can help a few of you guys out there who may have done a little bit of damage to your A m D process, sir.

 As always, Thank you very much for watching if you enjoyed this video lever like on it leave a dislike of you didn't subscribe to the channel if you haven't done so already, I'm going to go and fix a few more broken processes now. 